Description Application guidelines
A water-borne copolymer that is designed for 1. Coating is formulated for application by brush,
application to rusted ferrous metal surfaces. When roller,airless or conventional spray.
properly applied the coating converts the rusted surface 2. Do not apply coating iftemperature is below 50 F
to a dark, stable organic iron compound. This product (10oC) or if relativehumidity is above 80%. Do not
has a low permeability factor and is impermeable to apply in foggy or misty weather or if rain is
oxygen and moisture while providing a rust free surface imminent. Mix thoroughly with power mixer before
ready for priming or finishpainting use.
3. Theoretical coverage is 687 sq. ft. /gal. @ 1 mil
It converts and primes rusted surfaces in one dry film thickness. Practical coverage rate will be
operation; dries to a hard, gloss finish combines lower and willdepend on surface roughness, depth
excellent flexibility,toughness and impact resistance. of rust and application losses, and will vary from
200to 300 sq.ft.per gallon.
Uses 4. Apply one coat of ENDCOR 460 to 2 - 3 mils dry
" Used as a primer over surfaces which have film thickness (5 - 7 mils wet film). Coating willdry
minimal surface preparation and turn dark within 10- 15minutes.
" Converts rust into a primed surface ready for 5. For maximum protection of badly corroded
priming or topcoating surfaces, apply a 2nd coat at 2 - 3 mils dry film
" For use in industrial, marine, chemical, refineries, thickness. Apply within 20 - 30 minutes of 1st coat
and pipeline to ensure complete chemical reaction with the
rusted surface.
Features
" Thinning
Outstanding adhesion tosubstrate
" If thinning is required use only clean water up to a
Low permeability to water vapor and oxygen
" maximum of 1/2 pint per gallon of coating. Never add
VOC compliant
" solvents toENDCOR 460.
Tolerance for lower standards of surface
preparation
" Cleanup
User friendly- single package system
Flush and clean brushes and rollers with clean warm
water before primer sets up.
Surface preparation
Apply Endcor 460 only over properly prepared
Mixing
surfaces. All loose rust should be removed by scraping,
wire brushing and washed with water. Remove oil and Mix to a uniform consistency with a power mixer.
grease by solvent wiping or cleaning with an alkaline
detergent. Remove loose and flaking rust, mill scale Drying Time
and old paint by power or hand wire brushing, chipping Endcor 460 is ready to be topcoated in 24 hours (See
and scraping. Follow by fresh water rinse to remove all technical data section).
residues

Bulletin 460
Storage Spillage and Disposal
Storeincool,dry placewithtemperature between 50F In case ofspillabsorbwithinertcleanupmaterial,then
and 100F (10oC and 38oC). Keep from freezing. place in a chemical waste container. Dispose of in
Keep containerclosedwhen notinuse. accordance withapplicableregulations.
Precautionary Information Material Safety Data Sheet
Do notbreathe vaporor spraymist. Avoid contactwith See MaterialSafety Data Sheet (MSDS) on this
eyes, skin and clothing. Use only with adequate product forcompletesafetyinformation.
ventilationduringmixingand application.Only open
containersina well-ventilatedarea.Wear appropriate, KEEP OUT OF THE REACH OF CHILDREN.
properlyfittedrespirator(NIOSHapproved) duringand
afterapplicationunless airmonitoring demonstrates FOR INDUSTRIAL USE ONLY.
vapor/mistlevelsare below applicablelimits.Follow
manufacture's directionsfor respiratoruse. Wear MADE INTHE USA
neoprene gloves, chemical goggles and protective
clothing,Inconfined areas requireda constant flow, KEEP FROM FREEZING.
hood-type respirator. Observe safety precautions
describedinOSHA regulations.
PHYSICAL PROPERTIES
Properties Endcor 460
GenericType Water-borne Copolymer
Color Clear
Volume Solids 43%
Weight pergallon 10.3lbs.(1.2kg./l.)
Viscosity 38 cpsat 100 RPM
Ph 1.9 1
VOC(VolatileOrganic Content) 0.52lb./gal.(62g./l.)
Temperature resistance(dry) 120F (49oC)
Dry filmthicknesspercoat 2-3mils (50-75 microns)
Wet filmthicknesspercoat 5-7mils (125- 175microns)
Theoreticalcoverageper gallon 687 @ 1mil
Applicationtemperature Normal Minimum Maximum
Ambient Air 60-85 F(16-29oC) 50 F(10oC) 100 F(38oC)
Substrate 60-85 F(16-29oC) 50 F(10oC) 120 F(49oC)
Coating Material 65-85 F(18-29oC) 60F(16oC) 90 F(32oC)
Humidity 30-70% 0 80%
DryingTime* at50 F(10oC) at 70 F(21oC) at 90 F(32oC)
To touch 30min. 15 min.` 10 min.
To recoat 40-60 min. 20-30 min. 10-15 min.
To topcoat 48 hrs. 24 hrs. 12 hrs.
Flashpoint Above 200F (93oC)
Shelf life 6months
*Drying timewilldependupon temperature,humidityand airflowover thesurface.Forstillairconditionsallowupto
doublethe dryingtimelistedintheabove chart.

• 
  
  

  Where good ideas come to the surface

  
  Contact: sales@coating-paint.com